+86-028-85255257
Description
FT-MTRQ-4S100 is a Four-Channel, Parallel,Fiber-Optic QSFP+ Avtive Optical Cable for 40G Base-SR4 Ethernet Applications. This transceiver is a high performance module for short-reach muti-lane data communication and interconnect applications.it integrates four data lanes in each direction with 41.25Gbps bandwidth. Each lane can operate during 4x1Gbps~4x10.3125Gbps.
These modules are designed to operate over multimode fiber systems using a nominal wavelength of 850nm. The electrical interface uses a 38 contact edge type connector. The optical interface uses an 12 fiber MTP(MPO) connector.
A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire QSFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.
Features
¡ñ Support Data Rate 4x1Gbps?4x10.3125Gbps
¡ñ 4 channels 850nm VCSEL array
¡ñ 4 channels PIN photo detector array
¡ñ DDM function implemented
¡ñ Single MPO connector receptacle
¡ñ Hot Pluggable QSFP+ form factor
¡ñ Single +3.3V power supply
¡ñ Power consumption less than 1W
¡ñ Operating case temperature: 0?+70°C
¡ñ Distance 1 m/3m/5m/10m/15m/20m/30m/50m/100m
Applications
¡ñ 1G/10G Ethernet
¡ñ Datacom/Telecom switch&router connections
¡ñ Data Aggregation and Backplane Applicationgs
¡ñ Infiniband transmission at 4ch QDR,FDR and EDR
Compliance
¡ñ Compliant with SFF-8436 Rev 2.7
¡ñ Compliant with IEEE 802.3ae
Specification
Absolute Maximum Ratings |
|
|
|
|
Parameter |
Symbol |
Min. |
Max. |
Unit |
Storage Temperature |
TS |
-40 |
+85 |
¡æ |
Supply Voltage |
VCC3 |
0 |
3.6 |
V |
Relative Humidity |
RH |
5 |
85 |
% |
Recommended Operating Conditions |
|
|
|
|
|
|
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Note |
Operating Case Temperature |
TC |
0 |
|
70 |
¡æ |
|
Power Supply Voltage |
VCC3 |
3.13 |
3.3 |
3.47 |
V |
|
ICC3 |
|
|
300 |
mA |
|
|
Power Dissipation |
PD |
|
|
1 |
W |
|
Data Rate per channel |
|
1 |
10.3125 |
|
Gbps |
|
Electrical Characteristic |
|
|
|
|
|
|
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Note |
Input differential impedance |
|
|
100 |
|
Ω |
|
Differential data input swing |
|
180 |
|
700 |
mV |
|
Differential data output swing |
|
300 |
|
850 |
mV |
|
Transition Time, 20 to 80% |
Tr, Tf |
28 |
|
|
ps |
|
AC common-mode input voltage tolerance(RMS) |
|
15 |
|
|
mV |
|
Two Wire Serial (TWS) Interface Clock Rate |
|
|
|
400 |
kHz |
|
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.